fereaway.blogg.se - Telemecanique altivar 08 manual english

Telemecanique altivar 08 manual english series#

switching power on inductive load (cos ϕ 0.3 or L/R = 10 ms) : 2 A for c 250 V or a 30 V +5 : 5 V, 10 mA max. switching power : 10 mA for a 24 V - Max.

(1) Fault relay contact, signals the state of the controller remotely (open when fault present or powered off) - LI1 : forward - LI2 : reverse - LI3/LI4 : 4 preset speeds : 1 = LSP + reference on AI1 (LI3 = 0, LI4 = 0) 2 = SP2 (LI3 = 1, LI4 = 0) 3 = SP3 (LI3 = 0, LI4 = 1) 4 = HSP (LI3 = 1, LI4 = 1)

ItH motor thermal protection current 6 - Start : the speed is displayed in Hertz (Hz) for example, for a 3000 rpm / 50 Hz motor : 20 Hz = 1200 rpm.

SP2 and SP3 speeds if necessary for 4 preset speeds.

acceleration ACC and deceleration dEC ramps.

speed reference, via LI3/LI4 and/or via a potentiometer on AI1 3 - Power up without giving a run signal 4 - Configure the motor nominal frequency bFr if it is other than 50 Hz 5 - Adjust, if the factory setting is not suitable :.

control (1 or 2 operating directions via LI1 and/or LI2).

motor (U - V - W - s) ensuring that it is connected to a 200/240 V supply.

Antes de intervenir en el variador,ġ - Mount the controller 2 - Connect according to the circuit diagram below : Prima di intervenire togliere l'alimentazione, attendere 1 min. Vor Eingriff ist das Gerä spannungslos zu machen, 1 min warten. Before servicing remove all power, wait 1 min. Avant toute intervention, couper la puissance, attendre 1 mn. Installation : - device vertical, ± 10° - minimum clearance for cooling : 50 mm around the controller 10 mm in front

Telemecanique altivar 08 manual english series#

Telemecanique Plc Manual – Plc Manual Use between 10 and 20 cm depending on applicationMaterials handling seriesLaser class IIFood and beverage processing series 1 Forked with integral amplifier for indexingAnalog output Position controlVery long sensing distance or accurate sensingHigh excess gain for resistance to accumulated dirtStainless steel version for resistance to harsh agentsThru-beam0. F 49 mA 60x Smart relays with relay or transistor outputs Relay outputs: On-delay, Off-delay, Pulse on energization with start on energization, Pulse on energization with star t on opening of remote control contact, Flashing with start during the OFF period, Flashing with start during the ON period, Star-delta starting with double On-delay timing, Star-delta starting with contact for switching to star connection. Plug-in connectors accelerate and simplify installation and commissioning removable memory cards enable bus configurations to be copied in a few seconds.Sequential Function Chart, Grafcet language: Auto Ajuste para simplicar la puesta en marcha y optimizar las prestaciones. Each set that contains tw o double break contact elements 1 N.

Variateurs de Vitesse Telemecanique Documents. Committed to maximizing your investment over the long-term, Schneider Electric makes it easy for you to develop your applications with complete peace of mind.For left hand cable mount, replace the first 1 after the “CE” telemecaniuqe a 2 example: For thermal overload relays for telesquemzrio with class 10 A unbalanced loads, with connection by screw clamp terminals, change the prefix in the references above from LRD except LRD-4 to LR3-D. Looking for manual variador telemecanique altivar Will be grateful for any help! Top.Author:Vok KajilarCountry:IranLanguage:English (Spanish)Genre:TravelPublished (Last):7 July 2014Pages:245PDF File Size:5.30 MbePub File Size:19.37 MbISBN:857-5-86795-212-7Downloads:17137Price:Free.Free Regsitration RequiredUploader:Telemecanique Automatizacion y Control Documents. Manual electrotcnico: Telesquemario – Schneider Electric Schneider Electric Espaa. Zelio Relay – Schneider Electric India RS Interface Relay. Rearme manual u automtico Visualizacin del disparo Para corriente alterna o continuaTelemecaniqueSchneider ElectricZona de regulacin Amperes A Manual electrotcnico -telesquemario telemecaniqueTechnology.